KNOWLEDGE / 2026.11.20

Hydraulic Test Bench: Types, Components and Power Unit Requirements

A hydraulic test bench checks pumps, motors, cylinders and valves before installation or after repair. Based on public standards and test bench makers' documents, this guide covers the main types, what a bench is made of, and how to specify the power unit that drives it.

Published:

Revised:

Types by component and their standards

Pumps and motors: ISO 4409:2019 specifies methods for determining the steady-state performance and efficiency of positive-displacement pumps, motors and integral transmissions, including requirements for the test installation, test procedures and presentation of results. China adopts it identically as GB/T 17491-2023, in force since October 2023.

Cylinders: ISO 10100:2020 specifies acceptance and function tests for hydraulic cylinders. China's GB/T 15622-2023 is a modified adoption, in force since June 2024.

Valves: GB/T 8104, 8105 and 8106-1987 cover test methods for flow, pressure and directional control valves; their 2022 review concluded they should be revised. Electrically controlled pumps have GB/T 23253-2009, an identical adoption of ISO 17559:2003.

Test pressures, oil-temperature tolerances and measurement accuracy classes are set in the body of each standard. Use the current official text.

Universal and dedicated benches

One universal bench can test several component types. In Schroeder's HTB, for example, pumps and motors are tested dynamically; pumps are checked for external leakage and volumetric efficiency in either direction at 200–2400 rpm; double-acting cylinders are tested for internal and external leakage at any piston position; and valves can be set and checked for leakage. Schroeder also notes the bench can break in pumps and motors to the manufacturer's specification before installation.

Other benches focus on cylinders and valves. HAINZL's universal test bench takes cylinders, sandwich and cartridge valves, proportional and servo valves, with motion, leakage, static pressure (up to 400 bar), high static pressure (up to 700 bar), friction and oil-temperature tests.

Typical components

The examples below come from two bench makers' documents. Actual configurations depend on each bench's specification.

Common parts of a test bench (manufacturer examples)

  • Power source: the Schroeder HTB main pump is a variable piston pump, 87 or 144 L/min at 345 bar, with a 76 L/min, 138 bar supplemental pump and a 378 L reservoir (HTB-50/100)
  • Loading: a test motor load of 275–670 ft-lbs depending on model, plus a load pump (Schroeder)
  • Measurement: a digital flow gauge, a tachometer for the tested pump or motor, a reservoir temperature gauge and separate pressure gauges for each circuit (Schroeder); pressure measurement accuracy of 0.5 % FS on a 600 bar range (HAINZL)
  • Filtration: full-flow 3 µm filtration with a panel light when an element needs changing (Schroeder); 6 µm pressure and return filters plus bypass filtration (HAINZL)
  • Oil temperature control: optional oil cooler and water- or air-cooled heat exchangers (Schroeder); an approx. 4.5 kW tank heater integrated in the hydraulic unit (HAINZL)
  • Monitoring and records: automatic monitoring of tank level, filter clogging and oil temperature, with test reports stored on the bench and measured values saved as CSV (HAINZL)

Bench power unit: keep the oil temperature stable

Pump catalog data always comes with measurement conditions. Rexroth A10VSO technical data applies at 1 bar absolute at the suction port and 16–36 mm²/s viscosity; Rexroth PGH characteristics were measured at 1450 rpm, 41 mm²/s and 50 °C; Danfoss GearMe Group 2 curves were taken with ISO VG46 mineral oil at 50 °C (28 mm²/s).

When oil temperature changes, viscosity changes, and with it leakage and efficiency. To compare measured values with a catalog or a standard, the bench has to hold oil temperature near the stated condition. That is why a bench power unit usually needs both heating, for cold starts, and cooling, for long runs under load. Danfoss recommends keeping fluid temperature between 30 °C and 60 °C in normal operation.

Cleanliness, pressure and flow, heat and noise

Cleanliness: dirty bench oil contaminates freshly rebuilt parts. Rexroth A10VSO requires at least ISO 4406 20/18/15, and PGH allows a maximum of 20/18/15. Keep the bench oil at least as clean as the tested component's maker requires.

Pressure and flow: the power unit's pressure, flow and speed range must cover the test conditions of the parts you test. Commercial benches state these in their specifications: Schroeder HTB tests at 0–345 bar; HAINZL's test cylinder circuit gives up to 180 L/min at 55 bar or up to 420 bar at 20 L/min.

Heat: pressure dropped across loading and relief valves turns almost entirely into heat. Lost power ≈ pressure × flow; in an NPTEL course example, 40 L/min relieved at 70 bar loses about 4.67 kW. Benches often run under pressure for long periods, so size the cooler for the maximum load case.

Noise: pump catalog noise values cover the pump alone. Rexroth notes that under unfavorable conditions the sound pressure level at the power unit's installation site can be 5–10 dB(A) higher. Allow for this when planning the test room.

What to prepare before specifying a bench power unit

Inputs

  • Component types and sizes to be tested, and the test standard to follow
  • Maximum test pressure and flow, speed and load range
  • Test oil grade and temperature, and the required cleanliness code
  • Longest continuous run under load, which sets the cooling capacity
  • Data that must be recorded and reported

References

The content above comes from the public documents below. Standards are cited by scope only; manufacturer figures are examples, not general requirements.

Sources

  • ISO 4409:2019 and ISO 10100:2020, ISO standard pages (abstract and status)
  • GB/T 17491-2023, GB/T 15622-2023, GB/T 8104/8105/8106-1987, GB/T 23253-2009, National Public Service Platform for Standards Information
  • Schroeder Industries, Hydraulic Test Bench HTB, catalog pp.87–89
  • HAINZL Industriesysteme, Universal test bench for hydraulic components, product info 2023-10 V03
  • Bosch Rexroth, data sheets RE 92711 (A10VSO) and RE 10223 (PGH)
  • Danfoss, Hydraulic Fluids and Lubricants 520L0463; GearMe Aluminum Group 2 Pump technical information
  • NPTEL course 112106175, Lecture 30–31 self-evaluation

FAQ

Frequently asked questions

What types of hydraulic test bench are there?

By the component tested: pump and motor benches, cylinder benches, valve benches, and universal benches that test several types. Test methods are in ISO 4409 / GB/T 17491, ISO 10100 / GB/T 15622 and GB/T 8104–8106.

Why must a test bench control oil temperature?

Pump and valve catalog data is measured at a stated oil temperature and viscosity, for example ISO VG46 at 50 °C. If the oil temperature drifts, measured leakage and efficiency cannot be compared with the catalog.

How do I estimate the bench cooler?

From the power throttled or relieved at maximum load: lost power ≈ pressure × flow. For example, 40 L/min relieved at 70 bar is about 4.67 kW. Use the relief valve heat calculator to check your case.

ENERGY INTO VALUE

Less idle running. More value.

Make each holding phase count. Stop the motor after motion, then recharge when pressure reaches the set threshold, reducing energy use and heat from continuous idle running.

Save 75% or more in short-motion, long-hold applications. Turn reduced electricity use into lower running costs and get more value from every clamping cycle.

Annual electricity cost savingkWh avoided × electricity tariff
Review the savings potential of your machine →