KNOWLEDGE / 2026.11.05

Hydraulic Power Unit Maintenance Checklist

Most hydraulic failures start with the oil: too hot, too dirty, wet or aerated. A short routine of checks catches these early. Use the intervals below as a starting point and follow the manuals of the components fitted.

Published:

Revised:

Every shift or day

Quick visual and gauge checks take minutes and catch problems before they damage the pump.

Daily checks

  • Oil level in the sight glass, with the system in its normal state
  • Oil temperature; Danfoss recommends 30–60 °C in normal operation
  • Unusual noise or foam, which can mean air entering at the suction side
  • Visible leaks at hoses, fittings, the valve block and cylinders
  • Filter clogging indicator

Filters and cleanliness

Solid particles can lock pistons or block valves. Cleanliness is expressed as an ISO 4406 code: three numbers for particles of at least 4, 6 and 14 µm per 100 mL, for example 20/18/13.

Component makers set a minimum. Bosch Rexroth requires at least 20/18/15 for its A10VSO pump, tightening to 19/17/14 when viscosity falls below 10 mm²/s, and notes that finer filtration extends pump life.

HYDAC recommends replacing filter elements every 6 months or when the clogging indicator trips, whichever comes first. An indicator that trips only during a cold start may be reacting to thick oil rather than a full element.

Oil change and oil analysis

For mineral oils, Danfoss’s general recommendation is a first change after 500 operating hours, then every 2000 hours or once a year. High temperature and pressure age oil faster and can call for earlier changes. Take at least one sample for lab analysis between changes.

What to look for in the report

  • Water: Danfoss gives about 200–500 ppm as a rough critical range for HLP mineral oil; water causes corrosion, cavitation, filter clogging and oxidation
  • Wear metals: watch the trend; a sudden rise signals wear failure ahead
  • Silicon (dust): Danfoss recommends a fluid change above 10–15 mg/kg
  • Particle count against the ISO 4406 target for the system

Accumulator precharge

If the unit holds pressure with an accumulator, precharge loss shortens holding time and makes the pump restart more often. HYDAC advises checking precharge within the first week of operation, after 3–4 months, and at least once a year after that. Charge with nitrogen only.

Safety during maintenance

Release pressure, including accumulator pressure, before opening the circuit. Danfoss advises avoiding skin contact with fluid or heated parts, especially above 60 °C.

References

Intervals and limits above come from the following public documents and are general guidance.

Sources

  • Danfoss, Hydraulic Fluids and Lubricants, Technical Information 520L0463, pp. 4, 10, 13, 15–17
  • Bosch Rexroth, A10VSO series 31, data sheet RE 92711, p. 5
  • Parker Hannifin, Guide to Contamination Standards, p. 3
  • HYDAC, RFLD/H Return-line filter Service Manual, §2.3
  • HYDAC, FPO 210 Series charging and gauging unit, user manual, p. 2

FAQ

Frequently asked questions

How often should hydraulic oil be changed?

A common general starting point (Danfoss) is 500 hours after start-up, then every 2000 hours or yearly. Oil analysis shows whether your conditions need shorter or allow longer intervals.

How often should filters be replaced?

HYDAC recommends every 6 months or when the clogging indicator trips, whichever is first.

Who should service the accumulator?

Trained staff with the correct charging equipment, using nitrogen only and after releasing system pressure.

ENERGY INTO VALUE

Less idle running. More value.

Make each holding phase count. Stop the motor after motion, then recharge when pressure reaches the set threshold, reducing energy use and heat from continuous idle running.

Save 75% or more in short-motion, long-hold applications. Turn reduced electricity use into lower running costs and get more value from every clamping cycle.

Annual electricity cost savingkWh avoided × electricity tariff
Review the savings potential of your machine →