KNOWLEDGE / 2026.11.09

Hydraulic Cylinder Force and Speed Calculator

Enter bore, rod diameter, pressure and pump flow. The calculator returns push and pull force, extend and retract speed, and both effective areas. The formulas below reproduce the area, force and flow table in Bosch Rexroth’s mill-type cylinder data sheet.

Published:

Revised:

Cylinder force and speed calculator

Theoretical static values: seal friction and back pressure are not included. 1 MPa = 10 bar.
Push force (extend)
31.42 kN
Pull force (retract)
21.91 kN
Extend speed
0.099 m/s
Retract speed
0.143 m/s
Piston area
12.57 cm²
Annulus area
8.77 cm²
Send these values to an engineer

Formulas

Piston area A1 = π × D² / 4. Annulus (rod-side) area A3 = π × (D² − d²) / 4, where D is the bore and d the rod diameter.

Force F [kN] = p [bar] × A [cm²] / 100. Push force uses A1, pull force uses A3, so a cylinder always pulls with less force than it pushes at the same pressure.

Flow q [l/min] = 6 × A [cm²] × v [m/s]; rearranged, speed v = q / (6 × A). For the same pump flow the cylinder retracts faster than it extends, because the annulus area is smaller.

Worked example: Ø40/22 cylinder at 250 bar

A1 = π × 4² / 4 = 12.57 cm²; A3 = π × (4² − 2.2²) / 4 = 8.77 cm².

Push force = 250 × 12.57 / 100 = 31.4 kN; pull force = 250 × 8.77 / 100 = 21.9 kN.

At 0.1 m/s the cylinder needs 6 × 12.57 × 0.1 = 7.5 l/min to extend and 5.3 l/min to retract. Rexroth’s RE 17332 table lists the same values: 12.56 cm², 31.40 kN and 7.5 l/min on the piston side; 8.76 cm², 21.90 kN and 5.3 l/min on the rod side.

What the result does not include

Rexroth labels its table forces as theoretical, static cylinder force. Seal friction, back pressure in the return line and the force needed to accelerate the load are not included, so size the cylinder and pressure with a margin set by your own design rules.

In a clamping fixture the pressure that matters is the one held at the cylinder during machining. Shanchuan SC-QT units stop the pump while pressure is held and restart it when pressure falls below the set level; the calculator itself is general and makes no claim about any Shanchuan model.

References

Formulas are derived from the table in the following data sheet.

Sources

  • Bosch Rexroth, Hydraulic cylinders mill type CDH1/CGH1/CSH1, data sheet RE 17332/07.17, p. 4

FAQ

Frequently asked questions

How do I convert MPa or psi to bar?

1 MPa = 10 bar; 1 bar ≈ 14.5 psi. Enter pressure in bar.

Why is the pull force lower than the push force?

On the rod side the rod takes up part of the piston area, so the same pressure acts on a smaller area (A3 instead of A1).

How do I find the pump flow needed for a cycle time?

Speed = stroke ÷ time. Then q = 6 × A × v. For example, a 200 mm stroke in 2 s is 0.1 m/s, which for a Ø40 bore needs about 7.5 l/min.

ENERGY INTO VALUE

Less idle running. More value.

Make each holding phase count. Stop the motor after motion, then recharge when pressure reaches the set threshold, reducing energy use and heat from continuous idle running.

Save 75% or more in short-motion, long-hold applications. Turn reduced electricity use into lower running costs and get more value from every clamping cycle.

Annual electricity cost savingkWh avoided × electricity tariff
Review the savings potential of your machine →